Strengths

• 
  Open source 3D printing pad based on Klipper
  
• 
  Precise 7-inch control screen
  
• 
  1024x600 Resolution
  
• 
  64-bit motherboard
  

Creality's Sonic Pad is Klipper-based 3D touchscreen printing compatible with most FDM printers, including pre-configured models like Ender-3 Pro/Ender-5 Plus/Ender-3 Max/Ender-3 S1 Plus/CR -10 Smart/CR-10S Pro V2/CR -10 V3/Ender-3S1/Ender-3S1 pro/Ender-3v2/Ender-3V2 NEO.


A powerful combination of software and hardware guarantees 3D printing performance, the Sonic Pad brings Klipper to its range of 3D printers with elegant hardware and an intuitive open source touchscreen operating system and at an attractive price.

Klipper is a firmware that emerged as an alternative to Marlin when the limited processing capabilities of 8-bit motherboards began to slow down printing speeds. Instead of using the 3D main motherboard of the printer as the primary processing powerhouse, Klipper is installed on a secondary Linux-based computer – typically a single board computer (SBC) like a Raspberry Pi – that takes care of heavy G-code processing, relegating the motherboard from the single-run printer with lightweight "Klippy" firmware.

Highly integrated Klipper features
The Creality Sonic Pad offers users a full suite of unique Klipper features, including high print quality and speed, resonance compensation (input shaping), linear pressure/feed, and flexible macros.

Connect easily, support custom requirements
The Creality Sonic Pad can connect to almost any FDM 3D printer available on the market via a USB cable.
In addition, Sonic Pad supports user-defined programmable macros, for personalized function.


Rich extensible interfaces
It is powered by a 64-bit processor and motherboard, and configures 4 USB ports, 1 RJ45 port and 1 WiFi module, carrying 2 GB RAM and 8 GB ROM, allowing remote control of printers.

Intuitive user interface and real-time preview
The Sonic Pad supports sliced u200bu200bmodel preview when using Creality Print, Ultimaker Cura, Prusa Slicer and Super Slicer.

Control access from multiple platforms
It can be controlled either by the built-in touchscreen, remotely on a phone, or by a PC from the web user interface when connected to a local network.


Open Source Commitment
Creality Sonic Pad follows the Open Source Community Guidelines.
Users will be free to modify and customize the source code.

Plug and Play
With the included setup manual, it's easy to get things set up.
Preconfigured for Ender-3 V2, Ender-3 S1 and Ender-3 S1 Pro, so you can get it up and running in seconds.
And it supports all models of Creality except CR-10SMART PRO.

General

Brand: Creality
Type: 3D Sonic stamp for printer
Color: Gray

Specification

SoC: CrealityT800
SoC data bus width: 64 bits
RAM: 2G
ROM: 8G
Wi-Fi standard: 802.11 b/g/n
USB port: USB 2.0x4
LAN port: RJ45 x 1 (100 Mbps)
Vibration sensor interface: 1
Rated voltage: 12V
Display type: IPS
Screen size: 7 inches
Display resolution: 1024x600
Multi-touch: Yes
President: Yes
Vibration sensor: Yes

Weight and size

Product weight: 0.46kg
Package weight: 1.2kg
Product size (L x W x H): 22.2x12.8x4cm
Package size (L x W x H): 28x24x6cm

Package contents

1 x Creality Sonic Pad
1 x Instructions for use